DynaVap
Dynavap - VonG Dark Wood
Dynavap - VonG Dark Wood
We created our analog vaporiser, the VonG, with real, sustainably sourced wood. We carefully sand, polish, and wax the VonG by hand to showcase the exquisite wood body that was designed to mate perfectly with water pieces.
With zero electronic parts to worry about, you have the freedom to take your vaporiser wherever you go and the independence to use virtually any heat source. That means you can now enjoy consistent and flavourful vapour from your dry herb or concentrates (DynaCoil adaptor sold separately) all while stretching your stash. The VonG is 3.5” long, which puts it high in the running for one of the smallest vapes ever. It comes in a VapCap shaped cardboard tube that you can use as easy storage.
Product Information
Product Information
- Made entirely in the USA
- Precision machined wooden rotating sleeve allows quick and easy air flow adjustment on the fly*
- Lightweight titanium condenser and crowns surrounding the wooden sleeve
- Notched dosing chamber functions as a built in grinder
- Adjust-a-Bowl feature allows you to adjust the size of the dosing chamber to your needs and is ideal for microdosing
- A form fitting profile that fits comfortably in the hand
- Tapered mouthpiece fits snugly in either 10 or 14mm female water piece openings
- Comes with a Captive Cap and will fit in any standard size DynaStash or SlimStash.
*Please note: This feature may be difficult to rotate under certain environmental conditions depending on temperature and humidity
Before purchasing a device, please read our Customer Liability and Waiver
Cleaning & Maintenance
Cleaning & Maintenance
Tools You'll Need:
- Isopropyl Alcohol (90% or higher)
- Small container
- Pipe cleaners or cotton swabs
- Microfiber cloth
- Optional: A soft bristle brush to go at any stubborn residue
Instructions
1. Make sure the DynaVap is completely cool, then carefully take apart each component:
- Cap: Slide it off the tip.
- Tip: Remove it from the midsection.
- Condenser: Carefully pull out the condenser (the inner tube) from the midsection.
- O-rings: Take note of the location of each O-ring so you can put them back correctly. Avoid soaking the O-rings in alcohol, as it can degrade the material over time.
2. Soak the Parts & let it seep (not the Cap)
- Place the tip, midsection, and condenser into a small container filled with isopropyl alcohol. Soaking for about 15-30 minutes should be plenty to loosen most of the residue. The longer you let it soak, the easier it will be to clean it.
- Tip: If you’re dealing with a lot of residue build up, leaving the parts to soak overnight can be a good idea.
3. Clean the Condenser
- After a good seep, use a pipe cleaner dipped in isopropyl alcohol to clean the inside of the condenser. Run the pipe cleaner through it a few times until it’s free from any residue or buildup. If it’s particularly dirty, a second round of soaking may be helpful.
4. Scrub the Tip and Cap
- Use a cotton swab or a small brush to clean any remaining build up on the tip and cap.
- Focus on the screen inside the tip, as it tends to collect material that can impact airflow and flavour.
- Be gentle but thorough to ensure every nook and cranny is clean.
5. Rinse and Dry
- Once everything is clean and free of residue, rinse each part under warm water to remove any residual alcohol.
- Be sure to make sure everything is completely dry when reassembling.
- Then, you can use a microfiber cloth to shine your device. This not only gives a good polish and a shine, but also helps dry it off.
6. Put Your DynaVap back together
- Now that each part of the vape is clean and dry, it’s time to put everything back together. Carefully place the O-rings back in their positions on the condenser and tip (when applicable). Re-insert the condenser into the midsection, slide the tip back on, and finish by putting the cap on the tip.
Use With
Use With
Share


